“We use the Speed-Loc™ Quick Change System on our deep tillage equipment. Very handy and don’t have to worry about losing any shovels. All we use is Bourgault Tillage Tools. The openers on our 8810 have hardly had any wear in the 1,500 acres we did and will be able to use them for next season too. Tough, rugged, and reliable!”
Trevor Nolan, Elkhorn, Manitoba
SPEED-LOC™ OPENERS, SWEEPS & SPIKES
Quickly change between BTT seed openers, fertilizer knives, sweeps and spikes.
Speed-Loc™ adapters allow BTT products to fit on a variety of machines.
NOT SURE WHAT SPEED-LOC™ ADAPTER FITS YOUR MACHINE?
Find your equipment and the adapter that’s required on theSpeed-Loc™ Adapter Chart.
ASSEMBLY, INSTALLATION & REMOVAL QUESTIONS?
See theSpeed-Loc™ Guide or videos for expert advice on the quick change system.
REMOVING PRODUCTS FROM THE SPEED-LOC™ ADAPTERS?
Remember to use the Speed-Loc™ Release Tool to remove openers, sweeps and spikes from the adapters.
NEED REPLACEMENT PARTS OR A SPEED-LOC™ DRIVER?
Find the right Speed-Loc™ Accessories to install, remove and maintain the quick change system.
SPEED-LOC™ SEED OPENERS
200-HOE-1700
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: This single shoot opener runs through the ground at a fairly vertical angle to provide less rock pulling. Provides 1-1/2″ to 1-3/4″ (38 – 44mm) seed spread. Works best with a 1″ (25mm) single tube seed boot.
Welded high-chrome tip included.
200-KNF-0810 / 0811
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: This low disturbance single shoot opener is low in draft and easy pulling. It is designed to work with 300-ATM-1035 of the Seed Boot System.
Welded tip with or without carbide included.
200-KNF-0813
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: The more vertical approach of this single shoot opener reduces rock pulling. It is designed to work with 300-ATM-1035 of the Seed Boot System.
Welded carbide tip included.
200-KNF-7501
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: This single shoot opener is used in conjunction with Technotill system.
Welded high-chrome tip included.
200-KNF-7510 / 7511
Fits: 200 Series Speed-Loc™
Fertilizer Type: Seed with Granular starter
Overview: Precise seed placement due to the funnel being close to the tip and to the bottom of the furrow. The funnel is reinforced with hard surfacing for longer wear life. The funnel fits Bourgault and Flexi-Coil square tube seed boots. Also works with the square tube seed boot.
Welded tip with or without carbide included.
200-KNF-7542
Fits: 200 Series Speed-Loc™
Fertilizer Type: Granular
Overview: This single shoot opener is perfect for heavy gumbo soils. The extra space between the tip and the tube reduce plugging.
Welded high-chrome tip included.
200-KNH-4000
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: This single shoot opener is designed to work with 300-ATM-1035 of the Seed Boot System.
Your choice of any single shoot replaceable tips. Sold separately.
200-KNH-4010
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: This funnel is reinforced with hard surfacing for longer wear life. This single shoot opener works with the square tube seed boot of the Seed Boot System. Also fits the Bourgault or Flexi-Coil square tube seed boot.
Your choice of any single shoot replaceable tips. Sold separately.
200-VRT-1040
Fits: 200 Series Speed-Loc™
Fertilizer Type: Granular
Overview: The vertical approach of this single shoot opener reduces rock pulling and soil throw.
Welded carbide tip included.
200-SPN-0200 / 0208
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: These spoons have a 2″ (51mm) spread. Available in 1/4″ (6mm) material or 5/16″ (8mm) material for increased wear life.
200-SPN-0308
Fits: 200 Series Speed-Loc™
Fertilizer Type: N/A
Overview: These spoons have a 3″ (76mm) spread. Available in 1/4″ (6mm) material or 5/16″ (8mm) material for increased wear life.
410-KNF-0800 / 0801
Fits: 410 Series Speed-Loc™
Fertilizer Type: N/A
Overview: Low disturbance, low draft single shoot opener provides easy pulling. It is designed to work with the 300-ATM-1031 of the Seed Boot System.
Welded tip with or without carbide included.
410-SPN-0308
Fits: 410 Series Speed-Loc™
Fertilizer Type: N/A
Overview: These spoons have a 3” (76 mm) spread. Available in 5/16” (8 mm) material (410-SPN-0308) for increased wear life.
Welded tip with or without carbide included.
SPEED-LOC™ FERTILIZER KNIVES
200-ASY-7523
Fits: 200 Series Speed-Loc™
Fertilizer Type: Non-Freeze NH3
Overview: NH3 is delivered through an engineered nylon insert. This prevents the moist soil from freezing up and building up on the knife keeping it narrow to reduce the disturbance with minimal gassing off.
Welded carbide tip included.
410-ASY-0823
Fits: 410 Series Speed-Loc™
Fertilizer Type: Non-Freeze NH3
Overview: NH3 is delivered through an engineered nylon insert. This prevents the moist soil from freezing up and building up on the knife keeping it narrow to reduce the disturbance with minimal gassing off.
Welded carbide tip included.
410-ASY-7523
Fits: 410 Series Speed-Loc™
Fertilizer Type: Non-Freeze NH3
Overview: NH3 is delivered through an engineered nylon insert. This prevents the moist soil from freezing up and building up on the knife keeping it narrow to reduce the disturbance with minimal gassing off.
Your choice of 3/4″ or 3″ carbide tips. Sold separately.
602-ASY-7523
Fits: 43°, 47° and 50° C-Shank
Fertilizer Type: Non-Freeze NH3
Overview: NH3 is delivered through an engineered nylon insert. This prevents the moist soil from freezing up and building up on the knife keeping it narrow to reduce the disturbance with minimal gassing off.
Your choice of 3/4″ or 3″ tips. Sold separately.
200-KNF-7521
Fits: 200 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3
Overview: The shorter tube length on this knife makes it better for cultivators and chisel plows. The welded tip is better for rocky conditions.
Welded tip with or without carbide included.
200-KNF-7531
Fits: 200 Series Speed-Loc™
Fertilizer Type: Hot Gas NH3
Overview: The shorter tube length makes this opener better for use on cultivators and chisel plows. The welded tip is better for rocky conditions.
Welded tip with or without carbide included.
200-KNF-7525
Fits: 200 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3
Overview: The longer tube makes this opener better for air seeders and air drills. The welded tip is better for rocky conditions.
Welded tip with or without carbide included.
410-KNF-0825
Fits: 410 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3
Overview: This opener is designed for heavy-duty use. The welded tip is better for rocky conditions.
Welded 3/4″ tip with or without carbide included.
410-KNF-0826
Fits: 410 Series Speed-Loc™
Fertilizer Type: Liquid N NH3 PSI
Overview: Designed for use with liquid fertilizer or NH3. This opener is designed for heavy-duty use.
Welded 3/4″ tip with or without carbide included.
410-KNF-0827
Fits: 410 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3
Overview: Designed for heavy-duty use with Hot Gas NH3 kits. This opener is better in rocky conditions.
Welded 3/4″ tip with carbide included.
410-KNF-0831
Fits: 410 Series Speed-Loc™
Fertilizer Type: Hot Gas NH3
Overview: This opener is designed for heavy-duty use. The welded tip is better for rocky conditions.
Welded 3/4″ tip with or without carbide included.
410-KNF-7540
Fits: 410 Series Speed-Loc™
Fertilizer Type: Granular
Overview: This opener is not recommended for seeding.
Welded 3/4″ tip with carbide included.
410-KNF-7560
Fits: 410 Series Speed-Loc™
Fertilizer Type: NH3 & Liquid Phos
Overview: Also available to fit 200 Series Speed-Loc™. The welded tip is better for rocky conditions.
Welded 3/4″ carbide tip included.
200-KNH-4020
Fits: 200 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3
Overview: The knife is only recommended on light duty units with light trips. Not recommended in rocky areas.
Your choice of any single shoot replaceable tips. Sold separately.
410-KNH-7524 / 7526
Fits: 410 Series Speed-Loc™
Fertilizer Type: Cold Flow NH3 or NH3 PSI
Overview: Designed for use with NH3. 410-KNF-7524 has 1/2″ tubes, 410-KNF-7526 has 1/4″ tubes.
Your choice of 3/4″ or 3″ carbide tips. Sold separately.