NORTH AMERICAN-MADE REPLACEABLE TIPS
Excessive wear on the side or above the nose creates a rounded-off tip that can’t adequately fracture the soil, leading to lost bushels in your bin with a risk of higher repair costs if tips break and cause holder damage. Follow these simple steps to do a quick check…
Replaceable tips with tungsten carbide inserts are available for use with single shoot, paired row, side band and fertilizer openers.
We partner with Leth Iron in Lethbridge, AB to cast our replaceable tips with high chrome material, providing North American-made products with superior wear resistance.
Quickly and easily install new tips with our stainless steel bolt and nut combos: 600-BNC-5000 and 200-BNC-3100. Proven to work when roll pins won’t.
200-TIP-0511
CARBIDE TIP
1/2″ (13mm) with carbide insert on the nose. Not recommended in highly abrasive conditions.
200-TIP-0800
CHROME TIP
3/4” (19mm) tip. Not recommended in highly abrasive conditions.
200-TIP-0801
CARBIDE TIP
3/4” (19mm) tip with carbide insert on the nose.
200-TIP-0802
CARBIDE TIP
3/4” (19mm) tip with extra long carbide on the nose for highly abrasive conditions.
CARBIDE TIP
3/4” (19mm) tip with extra long carbide on the nose and sides for highly abrasive conditions. The same as 200-TIP-0802 but with the addition of the side carbide inserts.
VERTICAL CARBIDE TIP
3/4” (19mm) vertical tip with extra long carbide on the nose for highly abrasive conditions.
VERTICAL CARBIDE TIP
1” (25mm) vertical tip with double carbide insert. Recommended for rocky and highly abrasive conditions.
CARBIDE SPREAD TIP
2” (51mm) tip with carbide insert on the nose to fracture the ground. Carbide inserts on the underside of the wings to maintain a sharp cutting edge.
CHROME SPREAD TIP
3” (76mm) tip. Not recommended in highly abrasive conditions.
CARBIDE SPREAD TIP
3” (76mm) tip with carbide insert on the nose and hard facing on the underside of the wings.
CARBIDE SPREAD TIP
3” (76mm) tip with carbide insert on the nose to fracture the ground. Carbide inserts on the underside of the wings to maintain a sharp cutting edge.
CARBIDE SPREAD TIP
4” (101mm) tip with carbide insert on the nose to fracture the ground. Carbide inserts on the underside of the wings to maintain a sharp cutting edge.
CARBIDE SPREAD TIP
3/4” (19mm) long-wearing single shoot tip with extra long carbide on the nose for highly abrasive conditions. Used for seeding or fertilizing (not for double shooting).
CARBIDE TIP
3-1/2” (89mm) paired row cast chrome tip with 3/4” (19mm) vertical separation of liquid, granular, or aqua NH3 fertilizer. Carbide insert on the nose for excellent penetration and wear resistance. Carbide inserts on the underside of the wing maintain a sharp cutting edge. Carbide inserts at the back of the underside of the wings seal the fertilizer trench prior to seed placement.
CARBIDE TIP
4” (102mm) paired row cast tip with carbide insert on the nose for excellent penetration and wear resistance. These tips have 3/4″ (19mm) vertical drainage trench. Carbide inserts on the underside of the wing to maintain a sharp cutting edge. This paired row liquid or granular double shoot tip has no vertical seed/fertilizer separation.
CARBIDE TIP
4” (102mm) paired row cast tip with extra long carbide insert on the nose for excellent penetration and wear resistance. These tips have a 3/4″ (19mm) vertical drainage trench. Carbide inserts on the underside of the wing to maintain a sharp cutting edge. This paired row liquid or granular double shoot tip has no vertical seed/fertilizer separation.
CARBIDE TIP
4” (102mm) paired row cast chrome tip with carbide insert on the nose for excellent penetration and wear resistance. Carbide inserts on the underside of the wing to maintain a sharp cutting edge.
This paired row liquid or granular double shoot tip has no vertical seed/fertilizer separation.
CARBIDE TIP
4” (102mm) paired row cast chrome tip with carbide insert on the nose for excellent penetration and wear resistance. These tips have 3/4”(19mm) vertical separation of granular, liquid, aqua NH3, or aqua NH3 + phos fertilizer. Carbide inserts on the underside of the wing maintain a sharp cutting edge. Carbide inserts at the back of the underside of the wings seal the fertilizer trench prior to seed placement.
610-TIP-4082 has additional carbide below the wings, along the sides of the fertilizer trench, to provide extra-wear life. Not recommended for use on Case IH 800/900 or NH P2070.
610-TIP-4085 for Europe only.
CARBIDE TIP
6” (152mm) paired row cast tip with carbide insert on the nose for excellent penetration and wear resistance. These tips have 3/4” (19mm) vertical separation of liquid, granular, aqua NH3, or aqua NH3 + phos fertilizer.
Carbide inserts on the underside of the wing maintain a sharp cutting edge. Carbide inserts at the back of the underside of the wings seal the fertilizer trench prior to seed placement. Additional carbide is placed along the sides of the fertilizer trench, below the wings, to provide extra-wear life.
CHROME TIP
Side band cast chrome TriMax™ Triple-Shoot System tip with carbide inserts on the nose and the underside of the wing for excellent penetration and wear resistance. The seed is placed in a 3/4” (19mm) band onto a firm seedbed. The starter fertilizer is placed to the side onto a slightly lower shelf than the seed.
612-TIP-0211 (left wing)
612-TIP-0212 (right wing)
Fits: Bourgault TriMax™ Triple-Shoot System
CHROME TIP
Side band cast chrome tip with carbide inserts on the nose and the wing for excellent penetration and wear resistance. The seed is placed in a 3/4” (19mm) band onto a firm, unfractured seedbed. Fertilizer is delivered in a band off to the side (right or left) on the same level as the seedbed.
612-TIP-0711 (left wing)
612-TIP-0712 (right wing)
Fits: Bourgault, C-Shank, Case IH, Morris, Väderstad Seed Hawk
CARBIDE TIP
Side band cast chrome tip with carbide inserts on the nose and the wing for excellent penetration and wear resistance. A carbide wafer on the bottom of the fertilizer trough prevents bottom wear and keeps the fertilizer trench open. The seed is placed in a 1-1/2” (38mm) band 3/4” (19mm) above and to the side of the fertilizer row after the fertilizer trench has been closed by the wing.
614-TIP-2711 (left wing)
614-TIP-2712 (right wing)
Fits: Bourgault, C-Shank, Case IH, Morris
CARBIDE TIP
3/4” (19mm) chrome fertilizer tip with carbide on the nose.
Fits: 410, 599, 600, 602 & 607 Series fertilizer knife holders.
CARBIDE TIP
3/4” (19mm) chrome fertilizer tip with extra long carbide on the nose.
Fits: 410, 599, 600, 602 & 607 Series fertilizer knife holders.
CARBIDE TIP
3/4” (19mm) chrome fertilizer tip with extra long carbide on the nose.
Fits: 410, 599, 600, 602 & 607 Series fertilizer knife holders.
CARBIDE TIP & WING
3/4” (19mm) carbide fertilizer tip and wing for liquid application. This allows vertical and horizontal separation when double-shooting with liquid.